3d touch autolevel
Napsal: 11.05.2020 12:05Ahoj dobastlil jsem si na rebela 3dtouch ale bohuzel to nemuzu rozchodit...
nastaveno podle tohoto videa....
ale problem je ze desku si to otuka kdyz v repetieru spustim bed height map i to udela mapu.. ale potom kdyz napisu G33 L0
tak u vsech mereni mam Z-probe:10.232 X:20.00 Y:20.00 zCorr:0.000 takze korekce neprobiha overeno i tiskem
kdyz zkusim nastavit korekci rucne G33 X145.00 Y10.00 Z0.000 tak bohuzel se to tak neulozi...
momentalne nastaveno
M321 S2 ; Deactivate auto level permanently
M323 S0 P1 ; Disable correction permanently
ale zkousel jsem to mit i povoleny a bezezmeny.. bohuzel moc nevladnu anglictinou....
prikladam konfiguraci o z probe
// #################### Z-Probing #####################
#define Z_PROBE_Z_OFFSET 0
#define Z_PROBE_Z_OFFSET_MODE 0
#define UI_BED_COATING 1
#define FEATURE_Z_PROBE 1
#define EXTRUDER_IS_Z_PROBE 0
#define Z_PROBE_DISABLE_HEATERS 0
#define Z_PROBE_BED_DISTANCE 10
#define Z_PROBE_PIN ORIG_Z_MIN_PIN
#define Z_PROBE_PULLUP 0
#define Z_PROBE_ON_HIGH 1
#define Z_PROBE_X_OFFSET 35
#define Z_PROBE_Y_OFFSET 10
#define Z_PROBE_WAIT_BEFORE_TEST 0
#define Z_PROBE_SPEED 2
#define Z_PROBE_XY_SPEED 150
#define Z_PROBE_SWITCHING_DISTANCE 1
#define Z_PROBE_REPETITIONS 1
#define Z_PROBE_USE_MEDIAN 0
#define Z_PROBE_HEIGHT 4
#define Z_PROBE_DELAY 0
#define Z_PROBE_START_SCRIPT "M340 P0 S700" //"M340 P0 S700"
#define Z_PROBE_FINISHED_SCRIPT "M340 P0 S1500" //"M340 P0 S1500"
#define Z_PROBE_RUN_AFTER_EVERY_PROBE ""
#define Z_PROBE_REQUIRES_HEATING 0
#define Z_PROBE_MIN_TEMPERATURE 150
#define FEATURE_AUTOLEVEL 1
#define FEATURE_SOFTWARE_LEVELING 0
#define Z_PROBE_X1 20
#define Z_PROBE_Y1 20
#define Z_PROBE_X2 160
#define Z_PROBE_Y2 20
#define Z_PROBE_X3 100
#define Z_PROBE_Y3 160
#define BED_LEVELING_METHOD 1
#define BED_CORRECTION_METHOD 0
#define BED_LEVELING_GRID_SIZE 20
#define BED_LEVELING_REPETITIONS 1
#define BED_MOTOR_1_X 0
#define BED_MOTOR_1_Y 0
#define BED_MOTOR_2_X 200
#define BED_MOTOR_2_Y 0
#define BED_MOTOR_3_X 100
#define BED_MOTOR_3_Y 200
#define BENDING_CORRECTION_A 0
#define BENDING_CORRECTION_B 0
#define BENDING_CORRECTION_C 0
#define FEATURE_AXISCOMP 0
#define AXISCOMP_TANXY 0
#define AXISCOMP_TANYZ 0
#define AXISCOMP_TANXZ 0
napada nekoho co je spatne uz si stim fakt nevim rady...
jeste prikladam komplet repetier firmware....
https://drive.google.com/drive/folders/ ... sp=sharing
nastaveno podle tohoto videa....
ale problem je ze desku si to otuka kdyz v repetieru spustim bed height map i to udela mapu.. ale potom kdyz napisu G33 L0
tak u vsech mereni mam Z-probe:10.232 X:20.00 Y:20.00 zCorr:0.000 takze korekce neprobiha overeno i tiskem
kdyz zkusim nastavit korekci rucne G33 X145.00 Y10.00 Z0.000 tak bohuzel se to tak neulozi...
momentalne nastaveno
M321 S2 ; Deactivate auto level permanently
M323 S0 P1 ; Disable correction permanently
ale zkousel jsem to mit i povoleny a bezezmeny.. bohuzel moc nevladnu anglictinou....
prikladam konfiguraci o z probe
// #################### Z-Probing #####################
#define Z_PROBE_Z_OFFSET 0
#define Z_PROBE_Z_OFFSET_MODE 0
#define UI_BED_COATING 1
#define FEATURE_Z_PROBE 1
#define EXTRUDER_IS_Z_PROBE 0
#define Z_PROBE_DISABLE_HEATERS 0
#define Z_PROBE_BED_DISTANCE 10
#define Z_PROBE_PIN ORIG_Z_MIN_PIN
#define Z_PROBE_PULLUP 0
#define Z_PROBE_ON_HIGH 1
#define Z_PROBE_X_OFFSET 35
#define Z_PROBE_Y_OFFSET 10
#define Z_PROBE_WAIT_BEFORE_TEST 0
#define Z_PROBE_SPEED 2
#define Z_PROBE_XY_SPEED 150
#define Z_PROBE_SWITCHING_DISTANCE 1
#define Z_PROBE_REPETITIONS 1
#define Z_PROBE_USE_MEDIAN 0
#define Z_PROBE_HEIGHT 4
#define Z_PROBE_DELAY 0
#define Z_PROBE_START_SCRIPT "M340 P0 S700" //"M340 P0 S700"
#define Z_PROBE_FINISHED_SCRIPT "M340 P0 S1500" //"M340 P0 S1500"
#define Z_PROBE_RUN_AFTER_EVERY_PROBE ""
#define Z_PROBE_REQUIRES_HEATING 0
#define Z_PROBE_MIN_TEMPERATURE 150
#define FEATURE_AUTOLEVEL 1
#define FEATURE_SOFTWARE_LEVELING 0
#define Z_PROBE_X1 20
#define Z_PROBE_Y1 20
#define Z_PROBE_X2 160
#define Z_PROBE_Y2 20
#define Z_PROBE_X3 100
#define Z_PROBE_Y3 160
#define BED_LEVELING_METHOD 1
#define BED_CORRECTION_METHOD 0
#define BED_LEVELING_GRID_SIZE 20
#define BED_LEVELING_REPETITIONS 1
#define BED_MOTOR_1_X 0
#define BED_MOTOR_1_Y 0
#define BED_MOTOR_2_X 200
#define BED_MOTOR_2_Y 0
#define BED_MOTOR_3_X 100
#define BED_MOTOR_3_Y 200
#define BENDING_CORRECTION_A 0
#define BENDING_CORRECTION_B 0
#define BENDING_CORRECTION_C 0
#define FEATURE_AXISCOMP 0
#define AXISCOMP_TANXY 0
#define AXISCOMP_TANYZ 0
#define AXISCOMP_TANXZ 0
napada nekoho co je spatne uz si stim fakt nevim rady...
jeste prikladam komplet repetier firmware....
https://drive.google.com/drive/folders/ ... sp=sharing